Add products by adding codes
Rod end FLURO GAXSW 6 – M6 male, right-hand, heavy-duty, maintenance-free PTFE
- Heavy-duty rod end FLURO GAXSW 6: M6x1 right-hand male thread, 6 mm bore, load capacity 9.8 kN static / 9.3 kN dynamic, PTFE liner. 1 pc
FLURO GAXSW 6 Rod End – M6 Right-Hand Male Thread, 6 mm Bore, Heavy Duty, Maintenance-Free (PTFE)
FLURO GAXSW 6 is a heavy-duty, maintenance-free rod end (also referred to as a rose joint, heim joint, spherical rod end, or threaded uniball) featuring an M6 right-hand external (male) thread and a 6 mm ball bore diameter. It supports a static load of up to 9.8 kN and a dynamic load of up to 9.3 kN, and thanks to its steel / PTFE sliding contact surface, it requires no lubrication throughout its entire service life.
The GAXSW 6 rod end has the exact same dimensions as the standard GASW 6, but offers a higher static load rating: 9.8 kN instead of 6.0 kN. This difference comes from the housing forged from 42CrMo4 quenched and tempered steel.
This rod end belongs to the GAXSW series manufactured by the German company FLURO-Gelenklager GmbH, built to dimension series K in accordance with DIN ISO 12240-4. This series is a heavy-duty variant of the GASW series, engineered for high compressive and tensile loads, making it ideal for motorsport, mechanical engineering, and any application where a joint must compensate for misalignment and operate with zero play.
Key Specifications at a Glance
- Manufacturer: FLURO-Gelenklager GmbH (Germany)
- Manufacturer designation: GAXSW 6
- Type: external (male) thread rod end, heavy duty, maintenance-free
- Thread: M6 (1 mm pitch), right-hand
- Ball bore diameter: 6 mm
- Static load rating: 9.8 kN
- Dynamic load rating: 9.3 kN
- Sliding pair: steel / PTFE
- Standard: DIN ISO 12240-4, dimension series K
- Sold as: 1 piece
Technical Specifications – FLURO GAXSW 6
| Parameter | Value (Metric) | Value (Imperial) |
|---|---|---|
| Thread (G) | M6 male, right-hand | – |
| Ball bore diameter (d) | 6 mm | 0.24" |
| Outer head diameter (D) | 20 mm | 0.79" |
| Ball / inner ring width (W) | 9 mm | 0.35" |
| Housing / outer ring width (T) | 6.75 mm | 0.27" |
| Center of bore to end of shank (L) | 36 mm | 1.42" |
| Overall length | 46 mm | 1.81" |
| Thread length (GM) | 21 mm | 0.83" |
| Tilt angle | 13° in each direction (26° total) | – |
| Maximum static load (C0) | 9.8 kN | 2203 lbf |
| Maximum dynamic load (C) | 9.3 kN | 2091 lbf |
| Limiting rotational speed | 530 rpm | 530 rpm |
| Weight | 20 g | 0.044 lb |
| Lubrication | maintenance-free – do not lubricate | – |
Construction and Materials
Housing (body with threaded shank)
The housing is forged from 42CrMo4 (AISI 4140) quenched and tempered steel and zinc-plated for corrosion protection. All sizes in the GAXSW series feature housings manufactured in this manner, which accounts for their increased static load capacity.
Race (bearing liner)
The race is made of free-cutting steel with a bonded PTFE sliding liner. This layer ensures maintenance-free operation of the joint with zero backlash.
Ball (inner ring)
The ball is manufactured from 100Cr6 (AISI 52100) bearing steel – hardened, ground, and polished.
Applications
GAXSW series rod ends are used in linkages that transmit axial forces along the rod while accommodating angular misalignment. Typical applications for the M6 size include:
- throttle linkages and light control rods,
- position and suspension travel sensor linkages,
- low-load adjustment mechanisms and levers,
- light tie rods and aerodynamic element mounts,
- karting and model making,
- joints in automation systems, small actuators, and precision devices.
Selecting a rod end for a specific joint must account for actual operating loads and an appropriate safety factor – this is the responsibility of the design engineer or installer.
Installation Guidelines
- A 6 mm (M6) bolt or pin passes through the ball bore.
- Secure the threaded shank using an M6 jam nut.
- The threaded shank should be engaged to a minimum depth of 1.5 times the thread diameter, i.e., at least 9 mm.
- The rod end is designed for oscillating movements; full rotations are recommended only briefly.
- Do not lubricate the rod end – grease and oil degrade the performance of the PTFE liner.
- To utilize the full tilt angle, use conical misalignment spacers on both sides of the ball.
Frequently Asked Questions
What thread does the FLURO GAXSW 6 rod end have?
The FLURO GAXSW 6 rod end has an M6 external (male), right-hand thread. The thread length is 21 mm.
What bolt size fits the GAXSW 6 bore?
The ball bore diameter is 6 mm, so it accommodates an M6 (6 mm) bolt or pin.
What load can the FLURO GAXSW 6 handle?
The maximum static load rating is 9.8 kN (2203 lbf), and the dynamic load rating is 9.3 kN (2091 lbf).
Does the GAXSW 6 rod end require lubrication?
No. The rod end is maintenance-free – the race features a PTFE sliding liner that must not be lubricated. The rod end does not have a grease nipple.
What is the difference between GAXSW 6 and GALXSW 6?
GAXSW 6 has a right-hand thread, whereas GALXSW 6 has a left-hand thread. Using a pair of right-hand and left-hand rod ends on a single linkage rod allows you to adjust its length without disassembly.
What is the tilt angle of the GAXSW 6 rod end?
The ball tilts 13° in each direction, for a total of 26°.
What materials is the FLURO GAXSW 6 made of?
The housing is forged from 42CrMo4 (AISI 4140) quenched and tempered steel and zinc-plated, the race is free-cutting steel with a bonded PTFE layer, and the ball is hardened, ground, and polished 100Cr6 bearing steel.
What is the difference between GAXSW 6 and GASW 6?
GAXSW 6 is the heavy-duty version. It features a housing forged from 42CrMo4 steel and a static load rating of 9.8 kN, whereas the standard GASW 6 is rated at 6.0 kN. The dimensions, thread, and dynamic load rating of both versions are identical, making them directly interchangeable in terms of mounting.
Is the price for a single piece?
Yes, the price is for 1 piece of the FLURO GAXSW 6 rod end.