Add products by adding codes
Rod end FLURO GALSW 35 – M36x2 male, left-hand, maintenance-free PTFE (uniball)
- Maintenance-free rod end FLURO GALSW 35: M36x2 left-hand male thread, 35 mm bore, load capacity 101.0 kN static / 206.0 kN dynamic, PTFE liner. 1 pc.
FLURO GALSW 35 Rod End – M36x2 Left-Hand Male Thread, 35 mm Bore, Maintenance-Free (PTFE)
FLURO GALSW 35 is a maintenance-free rod end (also referred to as a rose joint, heim joint, spherical rod end, or threaded uniball) featuring an M36x2 left-hand external (male) thread and a 35 mm ball bore diameter. It supports a static load of up to 101.0 kN and a dynamic load of up to 206.0 kN, and thanks to its steel / PTFE sliding contact surface, it requires no lubrication throughout its entire service life.
A left-hand thread is most commonly paired with a right-hand GASW 35 rod end at the opposite end of a linkage rod. This allows the overall length of the rod to be adjusted simply by rotating it, without disconnecting the assembly.
This rod end belongs to the GALSW series (the left-hand threaded counterpart to the GASW series) manufactured by the German company FLURO-Gelenklager GmbH, built to dimension series K in accordance with DIN ISO 12240-4. Designed for operation under dynamic loads, this series excels in motorsport, mechanical engineering, and any application where a joint must compensate for misalignment and operate with zero play.
In size 35, the rod end has a 35 mm ball bore diameter, whereas the shank thread is M36x2 – fine-pitch, with a 2 mm pitch, rather than a standard M36 thread with a 4 mm coarse pitch. Therefore, pay attention to the thread pitch when selecting a nut or an internally threaded rod.
Key Specifications at a Glance
- Manufacturer: FLURO-Gelenklager GmbH (Germany)
- Manufacturer designation: GALSW 35 (ISO designation equivalent: GAKL 35 PW)
- Type: external (male) thread rod end, maintenance-free
- Thread: M36x2 (fine pitch, 2 mm pitch), left-hand
- Ball bore diameter: 35 mm
- Static load rating: 101.0 kN
- Dynamic load rating: 206.0 kN
- Sliding pair: steel / PTFE
- Standard: DIN ISO 12240-4, dimension series K
- Sold as: 1 piece
Technical Specifications – FLURO GALSW 35
| Parameter | Value (Metric) | Value (Imperial) |
|---|---|---|
| Thread (G) | M36x2 male, left-hand | – |
| Ball bore diameter (d) | 35 mm | 1.38" |
| Outer head diameter (D) | 80 mm | 3.15" |
| Ball / inner ring width (W) | 43 mm | 1.69" |
| Housing / outer ring width (T) | 28 mm | 1.10" |
| Center of bore to end of shank (L) | 125 mm | 4.92" |
| Overall length | 165 mm | 6.50" |
| Thread length (GM) | 73 mm | 2.87" |
| Tilt angle | 19° in each direction (38° total) | – |
| Maximum static load (C0) | 101.0 kN | 22706 lbf |
| Maximum dynamic load (C) | 206.0 kN | 46311 lbf |
| Limiting rotational speed | 110 rpm | 110 rpm |
| Weight | 1600 g (1.6 kg) | 3.53 lb |
| Lubrication | maintenance-free – do not lubricate | – |
Construction and Materials
Housing (body with threaded shank)
The size 35 housing is forged from C22 quenched and tempered steel and zinc-plated for corrosion protection. In the GALSW series, housings from size 14 upwards are forged, while smaller sizes (up to and including size 12) are machined from free-cutting steel.
Race (bearing liner)
The race is made of free-cutting steel with a bonded PTFE sliding liner. This layer ensures maintenance-free operation of the joint with zero backlash.
Ball (inner ring)
The ball is manufactured from 100Cr6 (AISI 52100) bearing steel – hardened, ground, and polished.
Applications
GALSW series rod ends are used in linkages that transmit axial forces along the rod while accommodating angular misalignment. Typical applications for the M36x2 size include:
- hydraulic and pneumatic cylinders,
- lever systems and linkages in machinery,
- construction, agricultural, and industrial machinery,
- heavy tubular structures, tie rods, and bracing,
- reaction rods in commercial and special-purpose vehicles (subject to load verification).
Selecting a rod end for a specific joint must account for actual operating loads and an appropriate safety factor – this is the responsibility of the design engineer or installer.
Installation Guidelines
- A 35 mm diameter bolt or pin passes through the ball bore.
- Secure the threaded shank using an M36x2 left-hand (fine-pitch) jam nut – a standard M36 nut with a 4 mm pitch will not fit.
- The threaded shank should be engaged to a minimum depth of 1.5 times the thread diameter, i.e., at least 54 mm.
- A left-hand thread is tightened counter-clockwise.
- Do not lubricate the rod end – grease and oil degrade the performance of the PTFE liner.
- To utilize the full tilt angle, use conical misalignment spacers on both sides of the ball.
Frequently Asked Questions
What thread does the FLURO GALSW 35 rod end have?
The FLURO GALSW 35 rod end has an M36x2 external (male), fine-pitch, left-hand thread. The thread length is 73 mm.
What bolt size fits the GALSW 35 bore?
The ball bore diameter is 35 mm, so it accommodates a 35 mm diameter bolt or pin.
What load can the FLURO GALSW 35 handle?
The maximum static load rating is 101.0 kN (22706 lbf), and the dynamic load rating is 206.0 kN (46311 lbf).
Does the GALSW 35 rod end require lubrication?
No. The rod end is maintenance-free – the race features a PTFE sliding liner that must not be lubricated. The rod end does not have a grease nipple.
What is the difference between GALSW 35 and GASW 35?
GALSW 35 has a left-hand thread, whereas GASW 35 has a right-hand thread. Using a pair of right-hand and left-hand rod ends on a single linkage rod allows you to adjust its length without disassembly.
What is the tilt angle of the GALSW 35 rod end?
The ball tilts 19° in each direction, for a total of 38°.
What materials is the FLURO GALSW 35 made of?
The housing is forged from C22 quenched and tempered steel and zinc-plated, the race is free-cutting steel with a bonded PTFE layer, and the ball is hardened, ground, and polished 100Cr6 bearing steel.
Is the price for a single piece?
Yes, the price is for 1 piece of the FLURO GALSW 35 rod end.